FDA publishes Final Guideline on GMP for Combination Products

Posted on Updated on

Image result for CGMP for Combination Products.

In the beginning of 2015 the FDA has published a draft guideline about GMP for Combination Products. Now the final version has been published. What are the differences between the draft and the final version of the FDA Guideline for Combination Products?

http://www.gmp-compliance.org/enews_05738_FDA-publishes-Final-Guideline-on-GMP-for-Combination-Products_15649,16021,15963,Z-VM_n.html

In the beginning of 2015 the FDA has published a draft guideline about GMP for Combination Products. Now the final version has been published. What are the differences between the draft and the final version? In the following you will find an overview:

The final guideline has expanded to now 59 pages (draft: 46 pages). And also the number of footnotes increased from 85 (draft) to 147 (final).

In the table of content there are one new subchapter (II B  Quality and Current Good Manufacturing Practice) and one new chapter (VII Glossary). Subchapter III C was expanded to definitions and terminology. In the following the table of content is listed:

I. Introduction

II. Background
A. Definition of a combination product
B. Quality and Current Good Manufacturing Practices
C. Overview of the final rule
D. The role of the lead center and other agency components

III. General Considerations for CGMP Compliance
A. Demonstrating compliance
B. Investigational products
C. Definitions and terminology
D. What CGMP requirements apply to a product or facility?
E. Control of changes to a combination product

IV. What do I need to know about the CGMP requirements specified in 21 CFR 4.4(b)?
A. Provisions from the device QS regulation specified in 21 CFR 4.4(b)(1)
B. Provisions from the drug CGMPs specified in 21 CFR 4.4(b)(2)
C. Combination products that include biological products and HCT/Ps

V. Application of CGMP requirements to specific types of combination products
A. Prefilled syringe
B. Drug-coated mesh
C. Drug Eluting Stent (DES)

VI. Contact Us

VII. Glossary

VIII. References

In the introduction it is explicitly stated, that “The final rule did not establish any new requirements”. In a footnote the guideline gives an explanation why the term “legacy” combination product has not been used.

In the new subchapter II B  (Quality and Current Good Manufacturing Practice) the guideline mentions, that “the core requirements embedded in these regulations provide for systems that assure proper design, monitoring, and control of manufacturing processes and facilities. This includes establishing a strong quality management system, using appropriate quality raw materials, establishing robust manufacturing and control procedures based on sound design principles, and detecting and investigating product quality deviations. In addition, these regulations call for ongoing assessment of systems and the implementation of corrective actions where appropriate”.

The final document introduces in Section C the new term “CGMP operating system”. This means the operating system within an establishment that is designed and implemented to address and meet the current good manufacturing practice requirements applicable to the manufacture of a combination product. A clarification about constituent parts of cross-labeled combination products is also implemented. Further, there is a new passage about the choice of the GMP-approach (QS regulation vs drug CGMPs) also regarding a streamlined approach and for companies manufacturing different products. Completely new is the passage with the title “Documentation of CGMP Approach”. Here you can also find hints that manufacturerers with products that have been on the market since before GMP for Combination Products (21 CFR 4) came into operation, have to be compliant too. The guideline requires that the information about the “CGMP operating system” should be shared with FDA investigators in the beginning of an inspection.

In the “Demonstrating compliance” subchapter (III A) there is additional information about crossreferenced approaches (21 CFR 820 vs 21 CFR 211 and vice versa). For investigational products (III B) you can find more detailed information about exemptions from part 820 regarding 21 CFR 820.30 (Design).

In the Definition and terminology section (III D) there are amendments regarding container closure aspects and kits. Section III D (What CGMP requirements apply to a product or facility?) details the responsibility of the owner of a combination product and CAPA procedures in shared facilities.

In section III E. (Control of changes to a combination product) information for single entity and co-packed combination product manufacturers has been amended. The passages in IV A (Provisions from the device QS regulation specified in 21 CFR 4.4(b)(1) with regard to 21 CFR 820 about Management Responsibility, Design Controls, Purchasing Controls and CAPA have been extended – including examples – and “modernised”. Terms like quality oversight and QTTP are now mentioned there. Vice versa the passages with regard to 21 CFR 211, 211.84. 211.103, 211.132, 211.137, 211.165, 211.166, 211.167, and 211.170,  (IV B  Provisions from the drug CGMPs specified in 21 CFR 4.4(b)(2)) have also been extended – likewise with examples – and have been “modernised” as well (e.g. parametric release is mentioned).

In the example about prefilled syringes (V A) one can find an amended passsage about Design Controls and a new section about Design History File. In the example about drug-coated mesh (V B) there has also been included a new section about Design History File. In the drug eluting stent example (V. C) there are amendments in the section about 21 CFR 211.184, 21 CFR 211.103 and 21 CFR 211.170. Furthermore all examples comprise editorial changes.

Completely new is the chapter VII (Glossary). The number of references (Chapter VIII) increased to 31 (draft: 19).

Summary:
There are a lot of changes from the draft to the final document. One chapter (Glossary) and a subchapter ( Quality and Current Good Manufacturing Practices) are new, but there are also new passages and amendments in the final document. Helpful are the examples that have been integrated.

Please also see the Guidance for Industry and FDA Staff: Current Good Manufacturing Practice Requirements for Combination Products for more details.

///////////

Advertisements

One thought on “FDA publishes Final Guideline on GMP for Combination Products

    DR ANTHONY MELVIN CRASTO Ph.D responded:
    January 13, 2017 at 3:23 pm

    Reblogged this on New Drug Approvals.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s